FRP Bottle Shape Cooling Tower

[vc_row full_width=”stretch_row”][vc_column][vc_column_text]

We offer Bottle Shaped Cooling Tower that is required for cooling application in numerous industries. The Round Shape FRP Cooling Tower may call as Bottle Shape . The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion.Bottle shape Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor ‘Minimum drift Losses’. Uniform distribution of hot water by rotating arm sprinkler.The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.

[/vc_column_text][vc_empty_space height=”60px” alter_height=”small” hide_on_mobile=””][vc_empty_space height=”90px” alter_height=”small” hide_on_mobile=””][/vc_column][/vc_row][vc_row][vc_column][vc_single_image image=”1657″ img_size=”full” alignment=”center”][/vc_column][/vc_row][vc_row][vc_column][vc_column_text]

General Features

[/vc_column_text][vc_empty_space alter_height=”medium” hide_on_mobile=””][/vc_column][/vc_row][vc_row][vc_column width=”1/2″][vc_column_text]

Design

Evaporative (FRP) Cooling towers are of vertical induced draft counter flow design with uniform water distribution and optimal heat transfer. Towers can be installed independent of wind direction. The tower casing is made from tough fiberglass and has sufficient strength to withstand high velocities and vibrations. The water collection sump is leak proof and avoids water spillage.

[/vc_column_text][vc_column_text]

Sprinkler

Automatic rotary sprinkler system made of Nylon 66 material, with rotary head and sprinkler pipe distributes the hot water over the entire space of the filler. Sprinkler pipes are non-clogging, require low pressure to operate and assures uniform water flow with minimal operating pump head. The FRP eliminators attached to sprinkler pipe are specifically designed for low pressure drop and minimises the drift loss of water.

[/vc_column_text][vc_column_text]

Fills

The fill is of rigid Poly Vinyl Chloride (PVC) and is of honeycomb design with very large contact surface area. The fill splits the air and water into several streams, increasing the time of contact and also heat transfer between water and air. The fill is in modules and is packed in the tower casing without any cutting for curves. The air pressure drop through the fill is negligible.

[/vc_column_text][vc_column_text]

Axial Fan

Specially designed energy efficient fans are of induced-draft axial type with adjustable pitch. Material chosen are non corrosive of plastic, FRP or aluminium alloy. The high efficiency design ensures low running cost and the lowest possible noise level. Fan blade pitch is factory set and dynamically balanced.

[/vc_column_text][/vc_column][vc_column width=”1/2″][vc_column_text]

Drift Eliminator

Reduces carry over losses of water. The eliminator is of rigid PVC (Applicable for square type cooling tower). The individual drift eliminators of S-shaped corrugated sheets are bonded with subsequent layers to create the structure. The entire area is thus divided into several fine S shaped mini zones each removing water droplets on the entire surface of the cell.

[/vc_column_text][vc_column_text]

Casing

The tower casing is made of tough fiberglass reinforced plastic (FRP) and has sufficient structural strength to withstand high wind velocities and vibrations. UV – stabilized resin is used along with gel coat for longer life. It is resistant to local impacts and even if slight damage occurs, local repairs can easily be done. The portion of casing housing fill and eliminator has a round cross section. The water collection sump, also of FRP, is leak proof & avoids water spillage.

[/vc_column_text][vc_column_text]

Motors

The motors are totally enclosed (IP55), flange type, 415 V, 3 ph, 50 Hz, induction weather proof with SS304 extended shaft and are specially designed for cooling tower application.

[/vc_column_text][vc_column_text]

Maintenance

Towers of lower capacity are completely factory assembled before despatch. At site the tower has just to be bolted, on the RCC / brick masonry foundation, thus saving a lot of installation time. Towers of higher capacity can easily be assembled at site and then installed in a manner similar to small towers. Maintenance is considerably reduced because fan, sprinkler fill and eliminator can easily be approached from the top without disturbing the cooling tower casing.

[/vc_column_text][/vc_column][/vc_row]